At a parking entrance the barrier must know whether a car is under it. It cannot close on a vehicle, and it should close behind a car that has passed. A loop detector is the classic way to know, and it sits unseen in the pavement. This guide explains how loop detectors work, how they are installed, and what to compare them with.
What a loop detector is
A loop detector has two parts: a wire loop laid in a cut in the pavement, and an electronic unit connected to the loop. The unit sends a current through the wire and watches it. When a metal vehicle sits over the loop, the electrical behaviour of the loop changes, and the unit reports a vehicle. It does not need the driver to do anything, and it works in the dark, in dust and in sun.
Presence loop and exit loop
Parking lanes often use two loops with different jobs. The safety loop lies under or beside the barrier and keeps it open as long as a vehicle is present, which prevents the boom from coming down on a car. The exit loop lies after the barrier and tells the controller that the vehicle has passed, so the boom can close. Some entrances also use a loop before the barrier to detect an approaching car and trigger the reader.
Installing the loop in the pavement
The installer cuts a slot in the pavement in the shape of the loop, lays the wire, seals it, and connects it to the detector with a twisted lead. The loop's size and the number of turns depend on the vehicles and the detector, so follow the detector's manual, and not a rule of thumb. Keep the loop away from large metal objects, such as reinforcement, if the manual says so, and seal the cut well, since water and movement damage wires.
Connecting it to the barrier controller
The detector's output goes to the barrier controller as a signal that a vehicle is present. The controller uses it to hold the boom open, and to close it after the vehicle has gone. Some barriers have anti-smash logic that uses this signal with others, such as a photocell. The ZKTeco CMP200, for example, is described on our site as supporting anti-smash and auto-close through an infrared, loop or radar detector. See also the ZKTeco ProBG3000 and our guide to barrier gates.
Radar, infrared and other detectors
A loop is not always the best choice:
- Radar detectors are mounted above or beside the lane and need no cutting of the pavement, which suits surfaces that must not be cut, or lanes that are resurfaced often.
- Infrared photocells use a beam across the lane and detect anything that breaks it, which makes them a common safety addition at the barrier.
- Other sensors exist for special cases. Ask the supplier which type suits your lane.
Many entrances use a loop for presence and a photocell as a second safety layer.
Maintenance and faults
Loops are robust, but they can fail. Road works, cracked pavement and water can cut or short the wire, and the detector's sensitivity may need adjusting. If the barrier stays open or does not detect a vehicle, check the loop connection, the detector and the settings. Include the loops in regular maintenance, and test the safety behaviour after any work on the pavement.
Mistakes to avoid
- Laying the loop without reading the detector's manual.
- Leaving the cut unsealed so that water reaches the wire.
- Relying on a single detector for the safety of the barrier.
- Forgetting to check the loop after the road is repaired or resurfaced.
Frequently asked questions
Can a loop detect a motorcycle or a small vehicle?
It depends on the loop design, the detector and its sensitivity setting. Confirm it in the detector's specification, or with your supplier, before relying on it for small vehicles.
When is radar a better choice than a loop?
When you cannot or do not want to cut the pavement, or when the surface will be resurfaced. Radar is installed above the lane instead of in it.
What happens to the loop when the road is resurfaced?
The loop is usually damaged and must be replaced. Plan it with the resurfacing work.
How do I test that the loop works?
Drive a vehicle over it and watch the detector's indicator and the barrier's behaviour, and test the barrier's response when the lane is occupied.
Send us a photo of your entrance with the button below, and we will suggest the detectors. See also our parking systems service page.
Need help choosing the right system?
Contact us on WhatsApp and send the site type, size, and service needed.
WhatsAppService page