Updated: 2026-10-23 · Access Points

Good WiFi coverage does not mean one strong signal at the router. It means a usable connection in every place where people work, with enough capacity for the devices that connect there. A single device in the middle of a villa or an office rarely achieves this, which is why access points are placed according to a plan. This guide explains how to plan that coverage in Riyadh.

Start with the site, not the device

Get the floor plan, or draw one, and mark where people actually use WiFi: desks, meeting rooms, reception, bedrooms, the majlis, storage areas. Then note what stands between those places and the likely access point locations. Concrete, reinforced columns, metal doors, glass partitions and lifts weaken the signal far more than open space does.

A signal that is strong but unstable is a common complaint. Strength tells you the device can hear the access point. It does not tell you that the access point can handle everyone who connects to it, so plan for both coverage and capacity.

Survey before you install

A site survey answers where the access points should go. There are two ways to do it:

  • Predictive survey: a plan on screen, using the floor plan and wall types, to estimate how many access points are needed and where.
  • On-site survey: walking the building with a test access point and a survey tool to measure signal and interference in the real rooms.

For a simple apartment a predictive plan may be enough. For offices, warehouses and buildings with thick walls, walk the site.

Placement that works

Mount access points on the ceiling or high on the wall, in the open and away from metal cabinets, so the signal spreads through the space. Place them near the middle of the area they serve, not at the far end, and avoid hiding them in cupboards. Keep spacing even: two access points close together do not double the signal, they compete for the same channels.

Use ceiling models in open spaces and wall-plate models in rooms that are separated by walls. The Grandstream GWN7625 (Wi-Fi 5), GWN7662 (Wi-Fi 6) and GWN7672 (tri-band Wi-Fi 7) are examples of indoor access points for different load levels. See the Grandstream page for the range.

Channels and bands

WiFi uses the 2.4 GHz band, the 5 GHz band, and the 6 GHz band on devices that support it. The 2.4 GHz band travels farther but is crowded, and has few separate channels. The 5 GHz and 6 GHz bands carry more traffic and suffer less from neighbours, but their range is shorter. A good plan keeps most devices on 5 GHz, leaves 2.4 GHz for older devices, and assigns channels so that neighbouring access points do not overlap.

Cabling and power

Run a data cable to each access point and power it from a PoE switch (IEEE 802.3af, at or bt, depending on the model). Wireless-only extension adds delays and uses airtime, so wire the access points whenever the building allows it.

Test after installation

Walk the site with a phone or laptop, run a speed test and a call in each important area, and move between areas to check the handover. Record the access point locations and settings for later maintenance.

Mistakes to avoid

  • Placing one device in the centre and expecting it to cover everything.
  • Judging coverage by signal bars alone.
  • Mounting access points behind metal or inside cupboards.
  • Adding access points without planning channels.

Frequently asked questions

How do I know where to place access points?

Use a survey: a predictive plan from the floor plan, or an on-site test with a test access point. Placement depends on walls and use, not on a rule.

Does adding more access points always improve the signal?

No. Extra access points on the same channels interfere with each other. More units help only when they are placed and tuned as part of a plan.

Why is the signal full but the connection slow?

The access point may be overloaded, the channel crowded, or the uplink limited. Check capacity, interference and the cabling, not only the signal strength.

Is 2.4 GHz still needed?

For older devices and long distances, yes. Keep it enabled, but move modern devices to 5 GHz or 6 GHz.

Send us the plan or a photo of the site through the button below, and we will suggest where the access points should go.

Need help choosing the right system?

Contact us on WhatsApp and send the site type, size, and service needed.

WhatsAppService page